FAQ

Frequently asked questions

Technological fundamentals

In abrasive flow machining (AFM), also known as pressure flow lapping, a highly viscous paste containing abrasive particles is pressed through the workpiece under controlled pressure. The paste acts as a flexible grinding tool that adapts to the geometry of the component.

The process simultaneously machines all surfaces that come into contact with the flow of the medium – in particular internal bores, channels and complex passages that cannot be reached with conventional tools.

What is the difference between abrasive flow machining, AFM and pressure flow lapping?

Abrasive flow machining (AFM) and pressure flow lapping all refer to the same process; the terminology simply differs depending on language and market tradition.

In German-speaking industrial markets, the terms “Strömungsschleifen” and “Druckfliessläppen” are commonly used, while internationally the term “Abrasive Flow Machining (AFM)” has become established. The underlying technology is identical.

Abrasive flow machining (AFM) and pressure flow lapping all refer to the same process; the terminology simply differs depending on language and market tradition. In German-speaking industrial markets, the terms “Strömungsschleifen” and “Druckfliessläppen” are commonly used, while internationally the term “Abrasive Flow Machining (AFM)” has become established. The underlying technology is identical.

Depending on the initial condition and workpiece geometry, abrasive flow machining can achieve surface finishes in the range of approximately Ra ± 0.1 µm. 

Abrasive flow machining is particularly suitable when conventional processes, such as mechanical deburring, reach their limits. This is typically the case with:

internal surfaces and channels that are not directly accessible;

complex intersecting bores and intersections;

components for which absolute reproducibility is required.

For highly sensitive components where thermal or chemical effects must be avoided, thermal energy method deburring (TEM) or electrochemical machining/deburring (ECM) may not be suitable. Abrasive flow machining is particularly preferred over TEM or ECM in medical technology applications.

The abrasive paste consists of a viscoelastic carrier medium containing abrasive particles of a defined grain size and concentration.

Viscosity, particle size and abrasive type are specifically adapted to the machining task. Typical abrasives range from silicon carbide and boron carbide through to diamond, depending on the required surface quality and workpiece material.

The formulation is a key factor in achieving reproducible results.

Depending on the initial condition and workpiece geometry, abrasive flow machining can achieve surface finishes in the range of approximately Ra ± 0.1 µm.

For Hygienic Design applications, for example in the pharmaceutical, chemical and food industries, surface roughness values of Ra < 0.38 µm are regularly achieved, meeting the relevant requirements for hygienic surfaces, piping and connections.

Yes. The fixture is individually designed and manufactured for each component or component family.

It directs the abrasive medium specifically through the areas to be machined while excluding surfaces that must not be processed. This custom-made fixture is a key quality factor and makes a significant contribution to process reproducibility.

In our video gallery, you can see all machining steps in detail. You can also take a look at our before-and-after examples.

Medical technology and implants

MMedical implants made of titanium place extremely high demands on surface quality and reproducibility.

Abrasive flow machining (AFM) is a proven method for this application because it works without thermal or chemical effects and can uniformly machine even complex implant geometries, such as threaded bores, threads, channels and undercuts.

The process can be validated and integrated into regulated manufacturing processes in accordance with ISO 13485.

Residual burrs or grooves on implant surfaces can cause increased abrasion, corrosion and tissue inflammation in the body.

In the case of bone screws, acetabular cups or spinal implants, burrs may also impair osseointegration.

Reliable and controlled deburring is therefore not only a quality issue but also a matter of patient safety.

Requirements vary depending on the type and function of the implant.

Sliding surfaces in joint implants typically require Ra values below 0.05 µm. For osseointegrated implants, such as dental implants, defined micro-roughness is desirable in order to promote cell adhesion.

Yes. Abrasive flow machining is a parameter-controlled and reproducible process.

Pressure, number of cycles, paste formulation and fixture geometry can all be fully documented and qualified. This makes the process compatible with validation requirements under ISO 13485 and FDA 21 CFR Part 820.

Stäheli has many years of experience in documenting machining processes for regulated industries.

More information and examples can be found here.

Chemicals, pharmaceuticals and foodstuffs

Weld seams in pipes, manifolds and valves are particularly susceptible to microbial growth and product deposits.

Abrasive flow machining can reduce weld reinforcement and heat tint inside pipes and fittings to roughness values of Ra < 0.38 µm, in line with Hygienic Design requirements according to EHEDG and 3-A Sanitary Standards.

The process also reaches areas that are inaccessible to rotating or manual tools.

For product-contact surfaces in the pharmaceutical and food industries, a surface roughness of Ra ≤ 0.8 µm is generally required, with Ra ≤ 0.38 µm in critical areas in accordance with EHEDG guidelines.

These values reduce dead zones, help prevent biofilm formation and enable reliable CIP/SIP cleaning.

Abrasive flow machining can achieve these values even on internal, difficult-to-access surfaces such as intersections, reducers and valve seats.

Yes. Abrasive flow machining is very well suited to polishing the inside of pipes, lines and fittings.

Because the abrasive medium processes the entire internal cross-section simultaneously, it creates a homogeneous and reproducible finish along the entire length.

This is particularly advantageous around weld seams, pipe radii and cross-sectional transitions.

Manifolds and multi-way valves contain internal intersections and edges that cannot be reached with conventional tools.

AFM presses the abrasive medium through all passages simultaneously and also deburrs intersecting edges between two bores.

The result is a smooth, burr-free internal surface without damaging the external geometry or sealing surfaces.

More information and examples can be found here.

Industrial parts and mechanical engineering

Intersecting bores in hydraulic blocks create sharp secondary burrs at the intersection points that are difficult to remove completely using mechanical methods.

AFM machines all channel walls and intersections in a single process step. The abrasive medium reaches every intersection and removes burrs reproducibly without the risk of leaving particles in the system.

Rough channel walls in oil passages increase flow resistance and can promote deposits.

AFM specifically reduces the roughness of internal channel surfaces, improving flow, minimising pressure losses and reducing the risk of particle entrainment caused by abrasion.

In high-performance transmissions and hydraulic systems, this can measurably improve efficiency and service life.

No. AFM is a purely mechanical-abrasive process and does not generate heat.

It therefore causes no structural changes, distortion or residual stresses.

Material removal is selective and controlled. It takes place primarily on burrs and surface roughness peaks rather than across the entire surface.

Tight tolerances and fits are therefore maintained.

More information and examples can be found here.

Aviation, aerospace and motorsports

Cooling channels in turbine blades and combustion chamber components are extremely narrow and geometrically complex, making them inaccessible to conventional tools.

AFM is one of the few processes capable of reproducibly deburring and smoothing these channels.

An improved internal channel surface reduces thermal load.

Yes. AFM is a fully documentable and qualifiable process with defined input and output parameters.

Process control, traceability and repeatability can be ensured.

The process is compatible with quality management systems according to AS9100 and with Nadcap-relevant process requirements.

In motorsports, AFM-machined components are specifically used to optimise flow characteristics.

Oil channels in connecting rods, crankshafts and engine blocks are smoothed to minimise flow resistance and improve the formation of the lubricating film.

At the same time, notches and micro-defects can be removed from the surfaces of highly stressed components, increasing fatigue strength.

Every gram and every bar of pressure loss counts – AFM addresses both

Yes. Due to its hardness and sensitivity to heat, titanium is difficult to machine with many conventional deburring processes.

AFM works without heat, and the abrasive paste formulation can be specifically adapted to titanium.

The process delivers reproducible results even on titanium components with narrow channels and complex internal geometries.

More information and examples can be found here.

Sensor technology and electronics

Sensor housings are often made from sensitive materials and contain bores with tight tolerances.

Mechanical deburring processes involve the risk of changing the bore geometry.

AFM selectively removes burrs at the edges without causing dimensional changes to the fitting surfaces.

Yes, depending on the minimum cross-sectional size.

AFM can machine channels and bores from approximately 0.5 mm in diameter, provided that the viscosity and particle size of the abrasive paste are adapted accordingly.

For even finer structures, special low-viscosity media are used.

Stäheli provides individual advice on the geometries for which AFM can be used effectively.

Burrs in electronic components can cause electrical short circuits, particularly if metal particles become detached and enter conductive areas.

Mechanical malfunctions caused by blocked channels or damaged sealing surfaces are also possible.

Burr-free components are therefore a functional requirement in sensor technology and electronics.

Yes. High-vacuum components place high demands on both surface quality and particle cleanliness.

Using abrasive paste specifically formulated for polishing requirements, low Ra values of < 0.2 µm can be achieved.

Subsequent cleaning processes using ultrasonic cleaning systems ensure the required level of particle cleanliness.

More information and examples can be found here. You can also take a look at our Success Story with

Metal parts from 3D printing

etal parts produced by 3D printing processes such as SLM, DMLS and EBM typically have rough, irregular surfaces, particularly inside internal channels, lattice structures and overhangs.

These areas cannot be reached with milling cutters, grinding tools or manual tools.

AFM is one of the few methods capable of reproducibly smoothing internal surfaces in additive-manufactured components.

Depending on the material and printing parameters, untreated SLM surfaces typically have Ra values between 5 and 20 µm.

AFM can reduce these values to Ra < 1 µm and, with multiple machining cycles, to Ra < 0.5 µm – even in internal cooling channels or flow channels.

This is particularly relevant for aerospace and medical technology components, where 3D printing is increasingly being used.

Conformal cooling channels in injection moulding tools are now frequently produced using 3D printing.

The rough internal walls of these channels increase flow resistance and reduce cooling performance.

AFM specifically smooths the internal channel surfaces, thereby improving heat transfer and flow efficiency without affecting the complex external geometry of the tool.

After printing, 3D-printed implants made of titanium or CoCr have rough, irregular surfaces that can promote protein deposits and undesirable cell adhesion.

AFM smooths these surfaces to defined Ra values and removes loose particles and oxide layers.

This improves biocompatibility while simultaneously allowing the surface roughness of osseointegrated areas to be selectively adjusted.

More information and examples can be found here.

Technical cleanliness & particle-free components

Technical cleanliness describes the condition of a component with regard to particle contamination and residual dirt after machining.

The relevant standards are VDA 19 for the automotive industry and ISO 16232 as an international standard.

They define limits for particle size, quantity and material on product-contact surfaces.

For safety-critical components used in hydraulic, electronic and medical technology systems, compliance with these standards is a fundamental quality requirement.

After machining, the abrasive medium is blown out of the component and the component is subsequently cleaned using extensive ultrasonic washing processes.

For medical products, the washing process is validated.

This is also relevant for hydraulic systems, sensor technology and electronic housings, where residual particles can cause malfunctions or failures.

In electronic components, loose metal particles, or “whiskers”, can cause electrical short circuits and render miniature housings unusable.

In hydraulic systems, residual particles can cause valve wear and system failure.

In medical technology, particles on implants represent a direct patient-safety risk.

AFM minimises these risks through its inherently low-particle process, and Stäheli can arrange for components to undergo cleanliness testing in accordance with VDA 19 / ISO 16232 after machining upon request.

Standards, certifications & compliance

Stäheli processes components for regulated industries such as medical technology, aerospace and pharmaceuticals.

The machining processes can be fully documented and are aligned with the requirements of ISO 13485 and ISO 9001.

Process parameters, fixture geometry and quality records are documented for every order.

Inspection reports and process documentation can be provided upon request.

The relevant process parameters are defined for every machining order, including pressure, number of cycles, paste specification, fixture geometry and, depending on the requirements, initial and final surface roughness.

This documentation enables complete traceability and provides the basis for process validation in accordance with ISO 13485.

Stäheli can provide the corresponding inspection reports and process records upon request.

In our video gallery, you can see all machining steps in detail. You can also take a look at our before-and-after examples.